Optimization design and simulation of transport and
ejection mechanism of airborne rice ejector

Abstract

Abstract: Rice seedling throwing has the advantages of high efficiency and small seedling damage. In this paper, a continuous type of automatic seedling conveying and ejecting mechanism is designed, and the conveying mechanism is designed and the force analysis is carried out. The maximum force of the intermediate copying frame is about 23.47N. The static analysis shows that the maximum stress of the copying frame is 36MPa, the maximum displacement and deformation is 0.6mm, and the maximum strain is 0.012, which meets the design requirements. The distance between the core of the bowl and the bottom surface is 9.71mm, and the relation between the minimum tumbling Angle and tumbling Angle speed and falling vertical distance is obtained. When the total length of the thimble is 50mm and the length of the boss is 5mm, the integrity of the bowl ejection is better. The ADAMS kinematics simulation test and orthogonal test were carried out with thimble mounting Angle and ejection force as test factors, and 2D displacement of the bowl after ejection as index. When the horizontal and vertical displacement of the simulation test reached the minimum value, the mounting Angle of the thimble was 25° and ejection force was 1.5N. The orthogonal test is carried out to verify the simulation results. When the experimental factors are consistent, the horizontal and vertical displacements reach the minimum values. The analysis shows that the installation Angle has a significant influence on the index, and the jacking force has a significant influence on the index. The research results can provide important reference for the design of rice seedling throwing device and the optimization of operation parameters.

Key words: , rice bowl seedling, design, agricultural machinery, ejector type, motion analysis

摘要： 水稻抛秧具有效率高、秧苗损伤小等优势。设计一种连续型秧苗自动输送及顶出机构，对输送机构进行设计及受力分析，得到中间仿形架受力最大约为23.47 N，静力学分析得出仿形架最大应力为36 MPa，最大位移变形量为0.6 mm，最大应变为0.012。对钵体顶出及斜抛过程进行受力分析，计算出钵体质心到底面距离为9.71 mm，得出钵体脱盘时的最小翻滚角度与翻滚角速度、下落垂直距离的关系。对顶针进行参数优化，当顶针总长为50 mm，凸台长度为5 mm时，钵体顶出完整性较好。以顶针安装角、顶出力为试验因素，以钵体顶出后的二维空间位移为指标，进行ADAMS运动学仿真试验及正交试验，当仿真试验水平和竖直位移达到最小值时，顶针安装角为25°、顶出力为1.5 N；进行正交试验验证仿真结果，当试验因素水平一致时，水平和竖直位移达到最小值。通过分析得出安装角对指标影响极显著，顶出力对指标影响较显著。研究结果可为水稻抛秧装置设计和作业参数优化提供重要参考。

关键词: 水稻钵苗, 设计, 农业机械, 顶出式, 运动分析

CLC Number:

S223.94

Ge Yiyuan, Guo Ningning, Qi Qinglong, Gao Hongcai. Optimization design and simulation of transport and ejection mechanism of airborne rice ejector[J]. Journal of Chinese Agricultural Mechanization.

葛宜元, 郭宁宁, 齐庆龙, 高洪才. 机载水稻抛秧装置输送顶出机构优化设计及仿真[J]. 中国农机化学报.

References

[1] 夏倩倩, 张文毅, 纪要, 等. 我国机械抛秧技术与装备的研究现状及趋势[J]. 中国农机化学报, 2019, 40(06):201-208.

Xia Qianqian, Zhang Wenyi, Ji Yao, et al. Research status and trend of mechanical seedling throwing technology and equipment in China [J]. Journal of Chinese Agricultural Mechanization, 2019, 40(06): 201-208.

[2] 杨敏丽, 彭健, 金剑, 等. 不同农用轮胎对东北黑土区土壤压实的影响[J]. 农业机械学报, 2023, 54(06): 85-93

Yang Minli, Peng Jing, Jin Jian, et al. Influence of agricultural tire technology innovation on soil compaction in black soil region Northeast China [J]. Transactions of the Chinese Society for Agricultural Machinery, 2023,54(06):85-93

[3] 沈春雷, 胡春雨, 葛雯, 等. 基于人—车—土系统的撒肥机组能耗与一源多用潜力分析[J]. 农业机械学报, 2023,54(S1): 419-426.

Shen Chunlei, Hu Chunyu, Ge Wen, et al. Energy consumption analysis and potential for one source for multi－purpose uses of fertilizer spreading units based on “Human－Vehicle－Soil” system [J]. Transactions of theChinese Society for Agricultural Machinery, 2023, 54(S1): 419-426.

[4] 丁启朔, 孙浩田, 李毅念, 等. 集约化生产条件下稻田土壤机械压实预测模型构建与验证[J]. 农业工程学报, 2023, 39(03): 42-51.

Ding Qishuo, Sun Haotian, Li Yinian, et al. Establishment and verification of soil mechanical compaction prediction model in paddy field under intensive production conditions [J]. Transactions of the Chinese Society of Agricultural Engineering, 2023, 39(03): 42-51.

[5] 付娟, 马仁明, 贾燕锋, 等. 机械压实对农田土壤性质及土壤侵蚀的影响研究进展[J]. 农业工程学报, 2022, 38(S1): 27-36.

Fu Juan, Ma Renming, Jia Yanfeng, et al. Research progress in the effects of mechanical compaction on soilproperties and soil erosion in farmland [J]. Transactionsof the Chinese Society of Agricultural Engineering, 2022, 38(S1): 27-36.

[6] 丁肇, 李耀明, 唐忠. 轮式和履带式车辆行走对农田土壤的压实作用分析[J]. 农业工程学报,2020,36(05):10-18.

Ding Zhao, Li Yaoming, Tang Zhong. Compaction effects of wheeled vehicles and tracked on farmland soil [J]. Transactions of the Chinese Society of AgriculturalEngineering, 2019, 36(05):10-18.

[7] 申屠留芳, 张炎, 唐立杰, 等. 水稻秧苗田间运输机的设计与试验[J]. 中国农机化学报, 2016, 37(05): 36-40.

Shentu Lifang, Zhang Yan, Tang Lijie, et al. Design and experiment on the rice seedling field transporter [J]. Journal of Chinese Agricultural Mechanization, 2016, 37(05): 36-40.

[8] 罗锡文. 对我国农业机械化科技创新的思考[J]. 农机科技推广, 2019(02): 4-7.

[9] 童纪氚, 戎雪利, 任萍, 等. 水稻无人机直播产量、效益分析及技术要点[J]. 中国稻米, 2024, 30(01): 98-100+107.

Tong Jichuan, Rong Xueli, Ren Ping, et al. Yield and benefit analysis of rice drone direct seeding and its technical points [J]. China Rice, 2024, 30(01): 98-100+107.

[10] 孙良, 姜凯雯, 周斌, 等. 取秧侧向零偏移的空间轨迹再生稻分插机构设计与试验[J]. 农业机械学报, 2024, 55(02): 101-108.

Sun Liang, Jiang Kaiwen, Zhou Bin, et al. Design and experiment of regenerated rice on space trajectory transplantation mechanism with zero lateral offset [J]. Transactions of theChinese Society for Agricultural Machinery, 2024, 55(02): 101-108.

[11] 张雅蓉, 谢方平, 符志勇, 等. 水稻机插秧同步智能侧深施肥装置研究现状与展望[J]. 农业装备与车辆工程, 2023, 61(08): 51-55.

Zhang Yarong, Xie Fangping, Fu Zhiyong, et al. Research status and prospect of intelligent side deep fertilization device for rice transplanting by machine [J]. Agricultural Equipment & Vehicle Engineering, 2023, 61(08):51-55.

[12] 张立国, 孙振鑫, 王泽东, 等. 水稻有序抛秧装置研究现状与发展趋势[J]. 农机使用与维修, 2024, (01): 57-61+80

Zhang Liguo, Sun Zhenxin, Wang Zedong, et al. Research status and development trend of rice orderly seedling throwing device [J]. Agricultural Machinery Using & Maintenance, 2024, (01): 57-61+80.

[13] 王琛.不同育插秧方式对水稻甬优2640秧苗农艺性状及产量的影响[J]. 福建稻麦科技, 2023, 41(03): 31-34.

Wang Chen. Effects of different cultivation and transplanting methods on agronomic characters of seedlings and yield for a rice cultivar yongyou 2640 [J]. Fujian Science and Technology of Rice and Wheat, 2023, 41(03):31-34.

[14] Jun jie D, Yu xiang Z, Zhi juan J, et al. Mining favorable alleles for rices heath blight resistance by association mapping [J]. Plant Growth Regulation,2021.

[15] Lohan S K, Narang M K, Singh M, et al. Actuating Force Required for Operating Various Controls of a Walk-Behind Type Paddy Transplanter Leading to Development of a Remotely Operated System [J]. Journal of Agricultural Safety and Health, 2021, 27(02).

[16] Li L, Zhang Z, Tian H, et al. Productivity and profitability of mechanized deep nitrogen fertilization in mechanical pot-seedling transplanting rice in South China [J]. Agronomy Journal, 2021, 113(02).

[17] 汪友祥, 彭洪巽. 2ZP-13型水稻有序抛秧机的研发与推广[J]. 农业机械, 2018, (11): 87-90.

Wang Youxiang, Peng Hongxun. 2ZP-13 rice sortingthrowing machine [J]. Farm Machinery, 2018, (11): 87-90.

[18] 敖礼林. 水稻育秧抛秧丰产栽培技术[J]. 科学种养, 2020, (05): 19-21.

[19] 周脉乐, 薛向磊, 钱孟波, 等.探出式蔬菜钵苗打孔移栽机构优化设计与试验[J]. 农业机械学报, 2020, 51(01): 77-83.

Zhou Maile, Xue Xianglei, Qian Mengbo, et al. Optimization design and experiment of perforation vegetable seedling transplanting mechanism with pucnch hole [J]. Transactions of the Chinese Society for Agricultural Machinery, 2020, 51(01): 77-83.

[20] 张振国, 张学军,曹卫彬, 等. 穴盘苗自动取苗装置的物料特性分析[J]. 江苏农业科学, 2015, 43(03): 348-351.

[21] 金鑫, 杜新武, 杨传华, 等. 蔬菜移栽穴盘苗自动输送装置设计与试验[J]. 农业机械学报, 2016, 47(07): 103-111.

Jin Xin, Du Xinwu, Yang Chuanhua, et al. Design andexperiment on automatic transporting mechanism for vegetable potted seedlings [J]. Transactions of the Chinese Society for Agricultural Machinery, 2016, 47(07): 103-111.

[22] 杨传华, 方宪法, 杨学军, 等. 基于PLC的蔬菜钵苗移栽机自动输送装置[J]. 农业机械学报, 2013, 44(S1): 19-23+18.

Yang Chuanhua, Fang Zhengxin, Yang Xuejun, et al. Automatic device mechanism of pot-seedling for vegetable transplanter based on PLC [J]. Transactions of the Chinese Society for Agricultural Machinery, 2013, 44(S1):19-23+18.

[23] 高攀, 陈平, 尹爱军, 等. 2024-T351铝合金喷丸残余应力松弛模型研究[J]. 机械强度, 2021, 43(06): 1316-1320.

Gao Pan, Chen Ping, Yin Aijun et al. Research on shot stress relaxation model of 2024-T351 aluminum alloy[J]. Journal of Mechanical Strength, 2021, 43(06): 1316-1320.

[24] 文永双,张俊雄,张宇, 等. 蔬菜穴盘苗插入顶出式取苗装置研制[J]. 农业工程学报, 2020, 36(22): 96-104.

Wen Yongshuang, Zhang Junxiong, Zhang Yu, et al. Development of insertion and ejection type seedling taking device for vegetable plug seedlings [J]. Transactions of the Chinese Society of Agricultural Engineering, 2020, 36(22): 96-104.

[25] 张雪琪, 弋景刚, 张秀花, 等. 铺放式茄科类蔬菜移栽机移栽装置结构设计[J]. 中国科技论文, 2018, 13(10): 1172-1176.

Zhang Xueqi, Yi Jinggang, Zhang Xiuhua, et al. Structure design of transplanting device for laying type transplanter of solanaceae vegetables [J]. China Sciencepaper, 2018, 13(10): 1172-1176.

Optimization design and simulation of transport and ejection mechanism of airborne rice ejector

机载水稻抛秧装置输送顶出机构优化设计及仿真

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Li Bin, Yang Xingyu, Liu Xiangxin, Gao Xiaolong. Research status and prospect of mechanized harvesting device for walnut [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 1-7.
[2]	Han Zhongdong, Liu Jiangtao, Yang Zhijie, Li Shanshan, Li Tao. Design and experiment of compound operation machine for precision sowing of maize [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 20-26.
[3]	Wang Xiang, Wang Junyue, , Bao Zhiliang, Meng Yugang, Gao Lei, Bao Wuyunbilige. Design and test of feeding roller of round baler based on SolidWorks Simulation [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 43-48.
[4]	Tian Huijuan, Huang Lüwen, , Tian Xu, Ren Liehong. Design of cattle collar based on multi‑sensor fusion [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 77-85.
[5]	Fan Yuhang, Song Weidong, Wang Jiaoling, Wang Mingyou, Ding Tianhang, Zhou Dehuan. Application progress of artificial neural network in the field of fruit and vegetable drying [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 112-119.
[6]	Yang Junru, , Yu Xiaodong, Li Ruichuan, , Xu Jikang, , Han Zongran, Li Yanchao, . Research and experiment on dynamic characteristics of tractor multi‑way valve throttling groove [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 126-131.
[7]	Yang Fan, , Teng Li, Sun Yitian, , Sun Yongjia, , Jiang Zhenhan, Hou Jialin. Development status and prospect of intelligent chassis of agricultural machinery [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 138-147.
[8]	Ma Zhiyan, , Wan Haidi, Chen Xuehai, , Shen Yang, , Zhou Minggang, . Research on the reconstruction method of maize three‑dimensional model in seeding stage based on RGB-D binocular vision [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 148-153.
[9]	Yu Chunhui, Chang Shuhui, , Zhang Fan, , Yao Jingfa, Meng Yu, Guo Yaqian. 面向大规模农田的农机跨区作业紧急调配研究 [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 196-203.
[10]	Li Jie, , Gao Shangbing, Yu Jiyuan, , Chen Xin, Li Shicong, Yuan Xingxing. Identification method of resistance to mung bean leaf spot disease based on PMMS-Net and chlorophyll fluorescence imaging [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 210-216.
[11]	Su Fei, , Wang Guanghui, Shi Yanxia, Jia Ran, Yan Yinfa, , Zu Linlu, . Leaf disease segmentation model of greenhouse tomatoes based on ResUnet with attention mechanism [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 228-233.
[12]	Yuan Yingchun, Zhang Ao, He Zhenxue, Zhang Ruochen, Lei Hao. Peach fruit real⁃time recognition in complex orchard environment based on improved YOLOv4-tiny [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 254-261.
[13]	Wang Ketao, Chen Shifeng, Chen Gui, Wei Jin, Meng Liwen, Chen Quancheng. Detection method of garden spherical hedge based on YOLOv5s [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 262-269.
[14]	Xu Jing, Sun Chitao, , Wang Peng, Yin Hang, Mi Qinghua, Liu Pingzeng. Design and implementation of monitoring system for farmland plastic film use information [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 302-307.
[15]	Xiong Zonghui, , He Zhiqi, Hu Pingping, Cao Dongsheng. Matching evaluation of supply chain procurement models for agricultural machinery products and services [J]. Journal of Chinese Agricultural Mechanization, 2024, 45(8): 308-316.