基于ANSYS Workbench的方捆机刀架静力学与模态分析

doi:10.13733/j.jcam.issn.20955553.2021.12.02

摘要/Abstract

摘要： 切割揉碎装置中刀架对秸秆切割揉碎方捆机的性能有重要影响。为避免作业过程中出现刀架结构强度不足和共振问题，运用SolidWorks软件建立秸秆切割揉碎方捆机的三维模型，将刀架模型简化后导入ANSYS Workbench软件，并对其分别进行静力学和模态分析。静力学分析结果表明：刀架在静载荷下最大位移为0.259 3 mm、最大应力为54.77 MPa，小于刀架材料Q345的屈服强度极限。模态分析结果表明：刀架前20阶固有频率的范围为32.61~257.83 Hz，与拖拉机产生的激励频率0~15 Hz不在同一区间内，因此秸秆切割方捆机在作业时不会产生共振现象。田间试验结果表明：秸秆切割揉碎方捆机纯工作小时生产率为4.49 t/h，成捆率为98.5%，规则草捆率为97.01%，抗摔率为95.52%，试验指标符合试验要求，刀架综合性能满足设计要求。

关键词: 切割揉碎方捆机, 刀架, 静力学分析, 模态分析

Abstract: The knife rest in the cutting and crushing device is an important bearing part in the straw cutting square baler, which impacts the performance of the straw cutting square baler. In order to avoid the problem of insufficient structural strength and resonance of the turret during the operation, a threedimensional model of the straw cutting square baler was established by using SolidWorks software, and the simplified turret model was imported into ANSYS Workbench software for static and modal analysis. The static analysis results showed that the maximum displacement and stress of the tool holder under static load were 0.259 3 mm and 54.77 MPa, which were less than the yield strength limit of Q345. The modal analysis results showed that the range of the first 20 natural frequencies of the cutter head was 32.61-257.83 Hz, which was different from the excitation frequency 0-15 Hz generated by the tractor, so the straw cutting square baler will not produce a resonance phenomenon during operation. The field test results showed that the pure working hour productivity of the straw cutting and kneading square baler was 4.49 t/h, the baling rate was 985%, the regular straw baling rate was 97.01%, and the fall resistance rate was 95.52%. The test indexes met the test requirements, and the comprehensive performance of the tool rest met the design requirements.

Key words: rest met the design requirements.
Keywords: straw cutting square baler, cutter frame, static analysis, modal analysis

中图分类号:

S225.2+2

王俊跃, 戴晓军, 王聪伟, 鲍志亮, 高磊, 张平. 基于ANSYS Workbench的方捆机刀架静力学与模态分析[J]. 中国农机化学报, 2021, 42(12): 9-16.

Wang Junyue, Dai Xiaojun, Wang Congwei, Bao Zhiliang, Gao Lei, Zhang Ping. Statics and modal analysis of square baler tool rest based on ANSYS Workbench[J]. Journal of Chinese Agricultural Mechanization, 2021, 42(12): 9-16.

参考文献

［1］　罗强军, 陈永生, 韩柏和, 等. 自走式打捆机的国内外研究进展［J］. 中国农机化学报, 2018, 39(12): 18-24.
Luo Qiangjun, Chen Yongsheng, Han Baihe, et al. Research progress of selfpropelled baler in China and abroad ［J］. Journal of Chinese Agricultural Mechanization, 2018, 39(12): 18-24.
［2］　王海超, 孙小添, 刘瑜, 等. 基于MATLAB的4YF-1300型大方捆打捆机喂入机构运动仿真分析与优化［J］. 中国农机化学报, 2021, 42(2): 31-36.
Wang Haichao, Sun Xiaotian, Liu Yu, et al. Simulation analysis and optimization of feeding mechanism of 4YF-1300 strapping machine based on MATLAB ［J］. Journal of Chinese Agricultural Mechanization, 2021, 42(2): 31-36.
［3］　孙治博, 刘晋浩. 林木联合采育机底盘车架设计与模态分析［J］. 江苏农业科学, 2013, 41(2): 375-377.
［4］　臧世宇, 吴崇友, 韩雄. 谷物联合收割机脱粒机机架模态分析［J］. 中国农机化学报, 2016, 37(5): 4-7.
Zang Shiyu, Wu Chongyou, Han Xiong. Analysis of combine harvester threshing machine modal ［J］. Journal of Chinese Agricultural Mechanization, 2016, 37(5): 4-7.
［5］　刘昌领, 陈建义, 李清平, 等. 基于ANSYS的六缸压缩机曲轴模态分析及谐响应分析［J］. 流体机械, 2012, 40(8): 17-21, 26.
Liu Changling, Chen Jianyi, Li Qingping, et al. Modal and harmonic response analysis of crankshaft of a six cylinders compressor by ANSYS ［J］. Fluid Machinery, 2012, 40(8): 17-21, 26.
［6］　柴苍修, 马力, 王元良, 等. 农用运输车车架有限元强度分析［J］. 拖拉机与农用运输车, 2002(1): 14-18.
Chai Cangxiu, Ma Li, Wang Yunliang, et al. Finite element strength analysis of agricultural transporter frame ［J］. Tractor & Farm Transporter, 2002(1): 14-18.
［7］　牛浩, 王震涛, 唐玉荣, 等. 基于ANSYS的残膜回收机提土筛膜组件机架静力学及模态分析［J］. 中国农机化学报, 2019, 40(12): 190-195.
Niu Hao, Wang Zhentao, Tang Yurong, et al. Statics and modal analysis of the frame of soillifting screen membrane component for residualfilm recycling machine based on ANSYS ［J］. Journal of Chinese Agricultural Mechanization, 2019, 40(12): 190-195.
［8］　赵艳梅. 基于ANSYS Workbench的某车架有限元分析及轻量化研究［D］. 郑州: 郑州大学, 2018.
Zhao Yanmei. Finite element analysis and lightweight research of a frame based on ANSYS Workbench ［D］. Zhengzhou: Zhengzhou University, 2018.
［9］　刘笑天. 万水ANSYS技术丛书ANSYS Workbench结构工程高级应用［M］. 北京: 中国水利水电出版社, 2019.
［10］　闻邦椿. 机械设计手册第1卷［M］. 北京: 机械工业出版社, 2018.
［11］　王利鹤, 赵永来, 崔红梅, 等. 基于ANSYS Workbench的深松机机架静力学分析及轻量化设计［J］. 重庆理工大学学报(自然科学), 2019, 33(2): 87-93.
Wang Lihe, Zhao Yonglai, Cui Hongmei, et al. Static analysis and lightweight design of subsoiler frame based on ANSYS Workbench ［J］. Journal of Chongqing University of Technology (Natural Science), 2019, 33(2): 87-93.
［12］　王景立, 刘选伟. 基于有限元法的深松机机架静力学分析［J］. 中国农机化学报, 2015, 36(6): 4-6.
Wang Jingli, Liu Xuanwei. Statics analysis of subsoiler frame based on finite element method ［J］. Journal of Chinese Agricultural Mechanization, 2015, 36(6): 4-6.
［13］　许超. 高地隙喷杆喷雾机自走式底盘机架的设计研究［D］. 石河子: 石河子大学, 2015.
Xu Chao. Highland gap lance sprayer selfpropelled chassis frame design research ［D］.Shihezi: Shihezi University, 2015.
［14］　董旭, 李志杰, 徐晶明. 基于ANSYS Workbench六自由度工业机器人动态特征分析［J］. 精密制造与自动化, 2014(3): 10-13, 43.
［15］　沈公威, 王公仆, 胡良龙, 等. 基于ANSYS的菜用甘薯茎尖切割有限元分析与试验［J］. 中国农机化学报, 2020, 41(4): 13-18.
Shen Gongwei, Wang Gongpu, Hu Lianglong, et al. Finite element analysis and experiment of cutting stem tip of vegetable sweet potato based on ANSYS ［J］. Journal of Chinese Agricultural Mechanization, 2020, 41(4): 13-18.
［16］　蔡力钢, 马仕明, 赵永胜, 等. 多约束状态下重载机械式主轴有限元建模及模态分析［J］. 机械工程学报, 2012, 48(3): 165-173.
Cai Ligang, Ma Shiming, Zhao Yongsheng, et al. Finite element modeling and modal analysis of heavyduty mechanical spindle under multiple constraints ［J］. Journal of Mechanical Engineering, 2012, 48(3): 165-173.
［17］　王东伟, 尚书旗, 韩坤. 4HJL-2型花生联合收获机摘果机构的设计与试验［J］. 农业工程学报, 2013, 29(14): 15-25.
Wang Dongwei, Shang Shuqi, Han Kun. Design and test of picking mechanism in 4HJL-2 peanut combines ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2013, 29(14): 15-25.
［18］　杜韧, 李佳栋, 赵忠贤, 等. 基于ANSYS Workbench圆盘割草压扁机机架模态分析［J］. 机械设计, 2019, 36(S2): 63-66.
［19］　郭正康. 论农用运输车的安全性能与设计［J］. 农业机械学报, 1992(4): 102-103, 109.
［20］　扈凯, 张文毅, 纪要, 等. 插秧机车架的动力学特性分析［J］. 中国农机化学报, 2018, 39(12): 78-82.
Hu Kai, Zhang Wenyi, Ji Yao, et al. Analysis on dynamic property of the frame of rice transplanter ［J］. Journal of Chinese Agricultural Mechanization, 2018, 39(12): 78-82.

[1]	吴紫晗, 李粤, 郭超凡, 贺宁波, 姚德宇, 位士全. 自走式香蕉秸秆粉碎还田机设计与仿真分析[J]. 中国农机化学报, 2022, 43(9): 40-46.
[2]	赖晓, 曾邦, 李尚平, 莫瀚宁, 何桂庆, 曹铂潇. 小型甘蔗收获机车架拓扑优化与试验[J]. 中国农机化学报, 2022, 43(7): 90-97.
[3]	刘曙光, 王家胜, 张梅, 尹宝全, 马云飞, 潘仕梅. 基于种绳模式胡萝卜播种机主体框架谐响应分析[J]. 中国农机化学报, 2022, 43(5): 1-6.
[4]	胡双燕, 胡敏娟, 张文毅, 蒋展. 辣椒穴盘苗茎秆力学特性试验与仿真研究[J]. 中国农机化学报, 2022, 43(3): 9-18.
[5]	胡双燕, 胡敏娟, . 可降解穴盘切割刀具优化设计与有限元分析[J]. 中国农机化学报, 2021, 42(9): 44-52.
[6]	任帅阳, 高爱民, 张勇, 韩伟, . 六旋翼植保无人机旋翼折叠机构有限元分析及拓扑优化[J]. 中国农机化学报, 2021, 42(9): 53-58+194.
[7]	奚小波;王昱;冒荧亮;赵映;张剑峰;张瑞宏;. 绿化养护矩形修剪打捆一体机设计与试验[J]. 中国农机化学报, 2021, 42(4): 41-48.
[8]	王贤斐, 张志元, 赵永满, 薛帅康, 李景彬, . 弧形扎膜钉齿设计与试验弧形扎膜钉齿设计与试验[J]. 中国农机化学报, 2021, 42(12): 24-29.
[9]	卢宇, 蒋延金, 陈立东, 杜清华, 李国昉, 杜福根, . 双U型棉花精量播种机设计与试验[J]. 中国农机化学报, 2021, 42(10): 34-41.
[10]	魏万成;戴飞;张方圆;宋学锋;张锋伟;毛雪杰;. 基于振动特性分析的枝条粉碎机转子系统结构优化[J]. 中国农机化学报, 2020, 41(9): 95-100+117.
[11]	郝秋菊;王槊;薛忠;潘睿;王刚;韩亚风;. 基于有限元分析的木薯削皮机夹持机构设计[J]. 中国农机化学报, 2020, 41(8): 90-94.
[12]	孙冬霞;樊平;王鹏军;王成;郝延杰;张爱民;. 有机肥施肥机关键部件的有限元分析及试验[J]. 中国农机化学报, 2020, 41(7): 9-15.
[13]	赵艳杰;胡天亮;胡靖明;毕阳;. 沙棘预破碎装置设计与有限元分析[J]. 中国农机化学报, 2020, 41(7): 87-93.
[14]	李敏通;杜雄梓;刘志杰;焦崇珊;朱盟盟;. 香瓜振动损伤特性试验研究[J]. 中国农机化学报, 2020, 41(6): 83-87.
[15]	史栋梁;王昱;牟剑;刘喜佳;涂彬;孙晓旭;. 基于变速箱体振动特性的阻尼层拓扑优化设计[J]. 中国农机化学报, 2020, 41(6): 149-153+193.