基于EDEM的气吸播种单体设计与试验

doi:10.13733/j.jcam.issn.2095-5553.2023.10.002

摘要/Abstract

摘要： 为研究气吸精量播种机播种株距不均匀的根本原因，基于离散单元法理论，以排种器及导种管共同组成的种子投送系统为研究对象，对种子投送过程进行理论建模，得到种子在导种管中运动的基本方程，并借助离散元软件EDEM对种子在导种管中运动轨迹进行仿真和碰撞分析。仿真结果表明：当种子与导种管首次碰撞入射角为4°~6.5°，反射角在2.5°以下时，种子的运动轨迹最为理想，此时种子沿导种管壁下滑，并在导种管末端沿圆弧段切线方向射出。并以此为依据对播种单体进行改制，进行田间试验验证，粒距合格指数稳定在到92%~93%，合格粒距变异系数小于30%，性能指标提升明显。

关键词: 气吸播种机, 播种单体, 导种管, 运动轨迹, 离散元

Abstract: In order to investigate the fundamental reasons for the uneven spacing of the air suction precision seeder, this paper is based on the discrete element method theory and takes the seed delivery system composed of a seed metering device and a seed guide tube as the research object. The theoretical modeling of the seed delivery process was carried out, and the basic equation of the seed movement in the seed guide tube was obtained. The movement trajectory of the seed in the seed guide tube was simulated and collision analyzed using the discrete element software EDEM. The simulation results showed that when the initial collision angle between the seed and the seed guide tube was 4°-6.5°, and the reflection angle was below 2.5°, the motion trajectory of the seed was the most ideal. At this time, the seed slided down the wall of the seed guide tube and shot out along the tangent direction of the arc segment at the end of the seed guide tube. Based on this, the seeding monomer was restructured and verified through field experiments. The qualified index of grain spacing remained stable at 92% to 93%, and the coefficient of variation of qualified grain spacing was less than 30%. The performance indicators improved significantly.

Key words: pneumatic seeder, seeder unit, seed tube, motion trajectory, discrete element

中图分类号:

S223.2

曹现超, , 杨东山, 杜新武, 金鑫, 王建华, 黄文龙, . 基于EDEM的气吸播种单体设计与试验[J]. 中国农机化学报, 2023, 44(10): 8-14.

Cao Xianchao, , Yang Dongshan, Du Xinwu, Jin Xin, Wang Jianhua, Huang Wenlong, . Design and experiment of pneumatic seeder unit based on EDEM[J]. Journal of Chinese Agricultural Mechanization, 2023, 44(10): 8-14.

参考文献

［1］　Li Y, Xiantao H, Tao C, et al. Development of mechatronic driving system for seed meters equipped on conventional precision corn planter ［J］. International Journal of Agricultural and Biological Engineering, 2015, 8(4): 1-9.
［2］　刘文忠, 赵满全, 王文明, 等. 气吸式排种装置排种性能理论分析与试验［J］. 农业工程学报, 2010, 26(9): 133-138.
Liu Wenzhong, Zhao Manquan, Wang Wenming, et al. Theoretical analysis and experiments of metering performance of the pheumatic seed metering device ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2010, 26(9): 133-138.
［3］　丁力, 杨丽, 刘守荣, 等. 辅助充种种盘玉米气吸式高速精量排种器设计［J］. 农业工程学报, 2018, 34(22): 1-11.
Ding Li, Yang Li, Liu Shourong, et al. Design of air suction high speed precision maize seed metering device with assistant seed filling plate ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2018, 34(22): 1-11.
［4］　李玉环, 杨丽, 韩英, 等. 勺夹式蚕豆精量排种器设计与试验［J］. 农业机械学报, 2018, 49(S1): 108-116.
Li Yuhuan, Yang Li, Han Ying, et al. Design and experiment of spoonclamping type metering device for faba beans ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2018, 49(S1): 108-116.
［5］　丛锦玲, 余佳佳, 曹秀英, 等. 油菜小麦兼用型气力式精量排种器［J］. 农业机械学报, 2014, 45(1): 46-52.
Cong Jinling, Yu Jiajia, Cao Xiuying, et al. Design of dualpurpose pneumatic precision metering device for rape and wheat ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2014, 45(1): 46-52.
［6］　李衍军, 刘瑞, 刘春晓, 等. 气送式排种器输种管内种子速度耦合仿真测定与试验［J］. 农业机械学报, 2021, 52(4): 54-61, 133.
Li Yanjun, Liu Rui, Liu Chunxiao, et al. Simulation and test of seed velocity coupling in seed tube of pneumatic seed metering device ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2021, 52(4): 54-61, 133.
［7］　王云霞, 张文毅, 严伟, 等. 气流辅助高速投种精量播种机压种装置设计与试验［J］. 农业机械学报, 2020, 51(10): 69-76.
Wang Yunxia, Zhang Wenyi, Yan Wei, et al. Design and experiment of seed pressing device for precision seeder based on air flow assisted seed delivery ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2020, 51(10): 69-76.
［8］　张宁宁, 康建明, 王小瑜, 等. 基于EDEM的滚筒式穴播器排种性能仿真与试验［J］. 中国农机化学报, 2021, 42(11): 1-6, 42.
Zhang Ningning, Kang Jianming, Wang Xiaoyu, et al. Simulation and experiment on seeding performance of peanut roller type hilldrop planter based on EDEM ［J］. Journal of Chinese Agricultural Mechanization, 2021, 42(11): 1-6, 42.
［9］　廖宜涛, 李成良, 廖庆喜, 等. 播种机导种技术与装置研究进展分析［J］. 农业机械学报, 2020, 51(12): 1-14.
Liao Yitao, Li Chengliang, Liao Qingxi, et al. Research progress of seed guiding technology and device of planter ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2020, 51(12): 1-14.
［10］　郭小军, 张海东, 吴进玲, 等. 基于EDEM的勺轮式葵花排种器离散元仿真研究［J］. 中国农机化学报, 2019, 40(2): 19-24.
Guo Xiaojun, Zhang Haidong, Wu Jinling, et al. Simulation research on spoontype seed metering device of sunflower seed based on EDEM ［J］. Journal of Chinese Agricultural Mechanization, 2019, 40(2): 19-24.
［11］　史嵩. 气压组合孔式玉米精量排种器设计与试验研究［D］. 北京: 中国农业大学, 2015.
Shi Song. Design and experimental research of the pneumatic maize precision seedmetering device with combined holes ［D］. Beijing: China Agricultural University, 2015.
［12］　丁力, 杨丽, 张东兴, 等. 气吸式排种器卸种机构设计与试验［J］. 农业机械学报, 2020, 51(1): 37-46.
Ding Li, Yang Li, Zhang Dongxing, et al. Design and test of unloading mechanism of airsuction seed metering device ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2020, 51(1): 37-46.
［13］　刘立晶, 杨慧. 基于Geomagic Design软件的导种管三维逆向工程设计［J］. 农业工程学报, 2015, 31(11): 40-45.
Liu Lijing, Yang Hui. 3D reverse engineering design on seed tube based on Geomagic Design software ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2015, 31(11): 40-45.
［14］　张建平, 李飞雄. 气吸式排种器排种均匀性的Monte Carlo模拟［J］. 农业工程学报, 1994, 10(1): 56-62.
Zhang Jianping, Li Feixiong. The Monte Carlo simulation on release homogeneity of suctiontype metering device ［J］. Transactions of the Chinese Society of Agricultural Engineering, 1994, 10(1): 56-62.
［15］　史嵩, 张东兴, 杨丽, 等. 基于EDEM软件的气压组合孔式排种器充种性能模拟与验证［J］. 农业工程学报, 2015, 31(3): 62-69.
Shi Song, Zhang Dongxing, Yang Li, et al. Simulation and verification of seedfilling performance of pneumaticcombined holes maize precision seedmetering device based on EDEM ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2015, 31(3): 62-69.
［16］　丁力, 杨丽, 张东兴, 等. 气吸式玉米排种器吸附姿态对投种性能的影响分析［J］. 农业机械学报, 2021, 52(7): 40-50.
Ding Li, Yang Li, Zhang Dongxing, et al. Effect of seed adsorption posture of corn airsuction metering device on seed feeding performance ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2021, 52(7): 40-50.
［17］　韩广森. 精密播种机输种管的研究［J］. 太原科技, 2003(5): 16-17.
Han Guangsen. The research on transmit seed tube of precision planter ［J］. Taiyuan Science and Technology, 2003(5): 16-17.

[1]	陈宇, 张涛, 林通, 庞有伦, 李相, 罗书强. 基于EDEM的废菌棒粉碎分离机设计与试验[J]. 中国农机化学报, 2023, 44(9): 104-111.
[2]	戚得众, , 阮晓松, , 孙强, , 杨文广, , 高伟周, . 芒果碰撞损伤及行间运输车降损性能研究[J]. 中国农机化学报, 2023, 44(9): 112-116.
[3]	闫建伟, 魏松, 张万萍, 张富贵. 白萝卜种子颗粒接触参数标定[J]. 中国农机化学报, 2023, 44(8): 1-11.
[4]	杨正, 李国锋, 石林榕, 王尊. 玉米种子静摩擦系数测定及离散元法验证[J]. 中国农机化学报, 2023, 44(8): 12-16.
[5]	李洪昌, , 高芳. 搅种托种型小麦气吸式精量排种器参数化设计与试验[J]. 中国农机化学报, 2023, 44(7): 9-15.
[6]	李娜, 刘磊, 徐鹏云, 李姜维, 姜海勇, 王伟. 基于离散元法的皂荚壳籽分离仿真与试验[J]. 中国农机化学报, 2023, 44(7): 163-169.
[7]	葛宜元, 矫洪成, 刘东旭, 梁秋艳, 杨传华. 基于EDEM的秸秆—土壤颗粒翻埋运动仿真及试验[J]. 中国农机化学报, 2023, 44(7): 229-235.
[8]	陈书法, 牛晏瑞, 芦新春, 杨进, 董志国, 冯博. 基于离散元法的扇贝肉壳分离直线振动筛仿真与试验[J]. 中国农机化学报, 2023, 44(5): 107-114.
[9]	徐兵, 郑德聪, 崔清亮. 基于EDEM的荞麦籽粒建模及振动筛分数值模拟[J]. 中国农机化学报, 2023, 44(5): 121-126.
[10]	邵伟, 张文毅, 纪要, 严伟, 刘宏俊. 甘薯除草部件设计与仿真研究[J]. 中国农机化学报, 2023, 44(4): 50-56.
[11]	章启祥, 刘发英, 杨振宇, 李继伟, 韩梦杰, 李学强. 基于离散元的马铃薯分选装置运行参数优化与试验[J]. 中国农机化学报, 2023, 44(4): 96-103.
[12]	丁力, 徐宇飞, 屈哲, 豆宇飞, 王万章, 李赫. 基于EDEM小麦收获机清选损失监测试验装置设计[J]. 中国农机化学报, 2023, 44(3): 13-21.
[13]	李昊, 张猛强, 尹勇, 张宏, . 流固耦合方法在农业工程中的应用[J]. 中国农机化学报, 2023, 44(2): 20-28.
[14]	王善文, 谢秋菊, 谢守勇, 邓成志, 黎展鹏. 双辊式食用菌培养料翻堆机翻堆装置设计与试验[J]. 中国农机化学报, 2023, 44(2): 46-52.
[15]	黎展鹏, 刘凡一, 魏志强, 邓成志, 王善文, 谢守勇, . 茎瘤芥种子离散元模型参数标定[J]. 中国农机化学报, 2023, 44(2): 83-90.