福建主栽花生品种果柄节点强度分析

doi:10.13733/j.jcam.issn.20955553.2022.05.004

摘要/Abstract

摘要： 为明确福建省花生的果柄节点强度情况，快速推动花生收获机械应用，对经省级认定的8个花生品种果柄节点强度进行测定。分析表明8个花生品种果柄节点强度在1.2~25.8 N之间，强度大于5 N的占97.33%，平均值为10.7 N。品种间果柄节点强度存在显著差异，其中福花4号的果柄节点强度均值最大，为11.40 N，莆花2号果柄节点强度最小，均值为9.91 N。品种和荚果饱满度互作存在极显著差异，大部分品种饱果果柄节点强度大于秕果。随着花生成熟，花生果柄节点强度极显著的减弱。覆膜和浇水可以提高花生果柄节点强度，但与露地栽培处理没有显著差异。果柄含水量与果柄节点强度存在极显著负相关。结果表明8个品种均适合花生联合收获机收获，为了减少机收造成的落果损失，对果柄节点强度较小的品种可以采取提前收获，或采用覆膜和浇水，在成熟中后期，减少田间土壤湿度，减少果柄含水量，以提高果柄节点强度。

关键词: 福建省, 珍珠豆型花生, 果柄节点强度, 联合收获, 机收损失

Abstract: In order to determine the peg strength of peanut varieties and promote the application of peanut mechanical harvesting in Fujian Province, the peg strength of 8 recognized varieties was tested. The result showed that the peg strength was between 1.2-25.8 N, with an average of 10.7 N, and more than 5 N accounted for 97.33%. The peg strength showed significant differences among different varieties. The average peg strength of Fuhua 4 was the largest (11.40 N), while that of Puhua 2 was the smallest (9.91 N). There were also significant differences between variety and pod plumpness, and the peg strength of full pod of most cultivars was greater than that of immature pod. The peg strength decreased significantly with increasing maturity of peanuts. Film mulching and watering improved the strength of peanut peg, but there was no significant difference with the open field treatment. There was a significant negative correlation between the water content of peg and the peg strength. Results showed that the 8 varieties were suitable for peanut combine harvesting. In order to reduce the fruit loss caused by mechanical harvesting, the varieties with small peg strength can be used during early harvest, or use film mulching and watering treatment, and reduce the soil humidity and water content of the peg in the middle and late stages of maturity.

Key words: Fujian Province, spanish peanut, peg strength, joint harvest, machine harvest loss

中图分类号:

S565.2

徐日荣, 陈湘瑜, 陈昊, 张玉梅, 蓝新隆, 唐兆秀. 福建主栽花生品种果柄节点强度分析[J]. 中国农机化学报, 2022, 43(5): 22-28.

Xu Rirong, Chen Xiangyu, Chen Hao, Zhang Yumei, Lan Xinlong, Tang Zhaoxiu.. Analysis of peg strength of main peanut varieties in Fujian Province[J]. Journal of Chinese Agricultural Mechanization, 2022, 43(5): 22-28.

参考文献

［1］张新友. 栽培花生产量,品质和抗病性的遗传分析与QTL定位研究［D］. 杭州: 浙江大学, 2011.
［2］田彩云, 郭心义. 我国花生生产发展及竞争力分析［J］. 粮食与油脂, 2004(4): 41-43.
［3］胡艳红, 崔林开, 郭金利, 等. 花生焦斑病菌的鉴定及生物学特性分析［J］. 植物保护学报, 2020, 47(1): 221-222.
Hu Yanhong, Cui Linkai, Guo Jinli, et al. Identification and biological characteristics of the peanut scorch spot pathogen Leptosphaerulina arachidicola ［J］. Acta Phytophylacica Sinica, 2020, 47(1): 221-222.
［4］唐兆秀, 陈树玉, 林琼, 等. 福建省花生机械化生产问题与对策研究［J］. 中国农机化学报, 2016, 37(8): 235-238.
Tang Zhaoxiu, Chen Shuyu, Lin Qiong, et al. Problems and countermeasures of peanut mechanical production in Fujian Province ［J］. Journal of Chinese Agricultural Mechanization, 2016, 37(8): 235-238.
［5］ Lopes D C. Potential crops for biodiesel production in Brazil: A review ［J］. World Journal of Agricultural Sciences, 2011, 7(2): 206-217.
［6］陈中玉, 高连兴, Chen Charles, 等. 中美花生收获机械化技术现状与发展分析［J］. 农业机械学报, 2017, 48(4): 1-21.
Chen Zhongyu, Gao Lianxing, Chen Charles, et al. Analysis on technology status and development of peanut harvest mechanization of China and the United States ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2017, 48(4): 1-21.
［7］高连兴, 陈中玉, Chen Charles, 等. 美国花生收获机械化技术衍变历程及对中国的启示［J］. 农业工程学报, 2017, 33(12): 1-9.
Gao Lianxing, Chen Zhongyu, Chen Charles, et al. Development course of peanut harvest mechanization technology of the United States and enlightenment to China ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2017, 33(12): 1-9.
［8］张冲, 胡志超, 邱添, 等. 国内外花生机械化收获发展概况分析［J］. 江苏农业科学, 2018, 46(5): 13-18.
Zhang Chong, Hu Zhichao, Qiu Tian, et al. Analysis of general situation of peanut mechanized harvest development at home and abroad ［J］. Jiangsu Agricultural Sciences, 2018, 46(5): 13-18.
［9］吴传云, 温浩军, 吴崇友, 等. 我国主要经济作物机械化主攻方向与主推技术［J］. 中国农机化学报, 2021, 42(12): 195-203.
Wu Chuanyun, Wen Haojun, Wu Chongyou, et al. Main directions and push technologies of economic crops mechanization in China ［J］. Journal of Chinese Agricultural Mechanization, 2021, 42(12): 195-203.
［10］陈有庆, 胡志超, 王海鸥, 等. 我国花生机械化收获制约因素与发展对策［J］. 中国农机化, 2012, 33(4): 14-17, 11.
Chen Youqing, Hu Zhichao, Wang Haiou, et al. Restrictive factors and development countermeasure for peanut mechanized harvesting in China ［J］. Chinese Agricultural Mechanization, 2012, 33(4): 14-17, 11.
［11］王伯凯, 吴努, 胡志超, 等. 国内外花生收获机械发展历程与发展思路［J］. 中国农机化, 2011, 32(4): 6-9.
Wang Bokai, Wu Nu, Hu Zhichao, et al. Experience and thought of development of peanut harvesting mechanization at home and abroad ［J］. Chinese Agricultural Mechanization, 2011, 32(4): 6-9.
［12］尚书旗, 王建刚, 王方艳, 等. 4H-2型花生收获机的设计原理及运动特性分析［J］. 农业工程学报, 2005, 21(1): 87-91.
Shang Shuqi, Wang Jiangang, Wang fangyan, et al. Design principle and analyses of the motion characteristics of 4H-2 type peanut harvester ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2005, 21(1): 87-91.
［13］王晓燕, 梁洁, 尚书旗, 等. 半喂入式花生摘果试验装置的设计与试验［J］. 农业工程学报, 2008, 24(9): 94-98.
Wang Xiaoyan, Liang Jie, Shang Shuqi, et al. Design and experiment of half feeding type peanut picker ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2008, 24(9): 94-98.
［14］关萌, 沈永哲, 高连兴, 等. 花生起挖晾晒后的果柄机械特性［J］. 农业工程学报, 2014, 32(2): 87-93.
Guan Meng, Shen Yongzhe, Gao Lianxing, et a1. Mechanical properties of peanut peg after digging and drying ［J］. Transactions of the Chinese Society of Agricultural Engineering, 2014, 32(2): 87-93．
［15］吴琪, 曹广英, 王云云, 等. 26个花生品种果柄强度研究［J］. 山东农业科学, 2016, 48(4): 47-49.
Wu Qi, Cao Guangying, Wang Yunyun, et al. Analysis on peg strength of 26 peanut varieties ［J］. Shandong Agricultural Sciences, 2016, 48(4): 47-49.
［16］迟晓元, 李昊远, 陈明娜, 等. 76个花生品种(系)果柄强度的研究［J］. 花生学报, 2018, 47(3): 14-18, 25.
Chi Xiaoyuan, Li Haoyuan, Chen Mingna, et al. Analysis on peg strength of 76 peanut varieties ［J］. Journal of Peanut Science, 2018, 47(3): 14-18, 25.
［17］鲁清, 李少雄, 陈小平, 等. 我国南方产区花生育种现状,存在问题及育种建议［J］. 中国油料作物学报, 2017, 39(4): 556-566.
Lu Qing, Li Shaoxiong, Chen Xiaoping, et al. Current situation, problems and suggestions of peanut breeding in Southern China ［J］. Chinese Journal of Oil Crop Sciences, 2017, 39(4): 556-566.
［18］刘宇锋, 苏天明, 苏利荣, 等. 我国南方花生产区栽培与施肥现状及对策［J］. 江西农业学报, 2019, 31(10): 1-9.
Liu Yufeng, Su Tianming, Su Lirong, et al. Current situation and strategy of peanut cultivation and fertilization in Southern China ［J］. Acta Agriculturae Jiangxi, 2019, 31(10): 1-9.
［19］郑奕雄. 南方花生产业技术学［M］. 广州: 中山大学出版社, 2009.
［20］厉广辉, 王兴军, 石素华, 等. 我国鲜食花生研究现状及展望［J］. 中国油料作物学报, 2018, 40(4): 604-607.
Li Guanghui, Wang Xingjun, Shi Suhua, et al. An overview of research progress and prospect for fresh peanut in China ［J］. Chinese Journal of Oil Crop Sciences, 2018, 40(4): 604-607.
［21］侯本军, 符书贤, 白翠云, 等. 海南鲜食花生种质资源农艺性状评价［J］. 广东农业科学, 2016, 43(8): 33-38.
Hou Benjun, Fu Shuxian, Bai Cuiyun, et al. Evaluation of agronomic characters of fresh edible peanut germplasm resources in Hainan Province ［J］. Guangdong Agricultural Sciences, 2016, 43(8): 33-38.
［22］王传堂, 王秀贞, 吴琪, 等. 鲜食花生感官品质主导分析、优异品系筛选与遗传力估算［J］. 花生学报, 2018, 47(4): 73-76.
Wang Chuantang, Wang Xiuzhen, Wu Qi, et al. Sensory quality of fresh green peanuts: dominance analysis, selection of elite lines and heritability estimates ［J］. Journal of Peanut Science, 2018, 47(4): 73-76.
［23］尹欣幸, 杨伟波, 符海泉, 等. 鲜食花生市场前景与研究现状分析［J］. 热带农业科学, 2019, 39(6): 111-116.
Yin Xinxing, Yang Weibo, Fu Haiquan, et al. Market prospect and research progress of fresheating peanuts ［J］. Chinese Journal of Tropical Agriculture, 2019, 39(6): 111-116.
［24］ Troeger J M, Williams E J, Butler J L. Factors affecting peanut peg attachement force ［J］. Peanut Science, 1976, 3(1): 37-40.
［25］胡志超, 王海鸥, 王建楠, 等. 4HLB-2型半喂入花生联合收获机试验［J］. 农业机械学报, 2010, 41(4): 79-84.
Hu Zhichao, Wang Haiou, Wang Jiannan, et al. Experiment on 4HLB-2 type half feed peanut combine harvester ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2010, 41(4): 79-84.

[1]	马宗雨, 万其号, 陈文星, 布库, 杨锦章, 杜文亮. 羊草种子脱出物料风筛清选装置设计与试验[J]. 中国农机化学报, 2022, 43(8): 96-105.
[2]	刘佳杰, 马兰, 向伟, 颜波, 文庆华, 吕江南. 4QM-4.0型麻类青饲料联合收获机割台结构设计与试验[J]. 中国农机化学报, 2022, 43(7): 20-25.
[3]	魏宏玲, 王小瑜, 陈进熹, 崔荣江. 中国大蒜机械化生产现状与发展思路探讨[J]. 中国农机化学报, 2022, 43(4): 175-182.
[4]	刘华伟, 张萍, 杨晓慧, 邓玉杰, 李柯莹, 张国海. 国内谷物联合收获机割台智能化现状与发展研究[J]. 中国农机化学报, 2022, 43(4): 189-197.
[5]	李国杰, 邓干然, 吴洪珠, 郑爽, 崔振德, 黄洁. 4UMZ—1400型后收集式木薯联合收获机设计与试验[J]. 中国农机化学报, 2022, 43(3): 1-8.
[6]	刘洋, , 杨善东, 魏忠彩, , 邱田元, , 盖金星, , 胡培杰. 甜菜生产全程机械化技术与装备研究进展[J]. 中国农机化学报, 2022, 43(3): 36-46.
[7]	李聿尧, 杨红光, 王冰, 吴峰, 顾峰玮, 范加力. 马铃薯联合收获薯土分离技术与装置研究[J]. 中国农机化学报, 2022, 43(10): 42-50.
[8]	陈旭, 关卓怀, 李海同, 沐森林, 张敏, 吴崇友. 油菜联合收获机含杂率在线检测系统设计与试验[J]. 中国农机化学报, 2022, 43(10): 127-134.
[9]	申海洋, 王公仆, 胡良龙, 王冰, 鲍国丞, 纪龙龙, . 4UZL-1型甘薯联合收获机刮板链提升机构设计与台架试验[J]. 中国农机化学报, 2021, 42(9): 7-17+121.
[10]	杨红光;胡志超;彭宝良;王冰;张延化;于昭洋;. 大蒜多行联合收获机秧果集送装置设计与试验[J]. 中国农机化学报, 2021, 42(7): 8-12.
[11]	俞国红;郑航;薛向磊;杨槐均;. 榨菜收获装备研究现状与展望[J]. 中国农机化学报, 2021, 42(6): 17-20.
[12]	陈进;张帅;李耀明;朱林军;夏慧;朱亚辉;. 联合收获机水稻破碎籽粒及杂质在线识别方法[J]. 中国农机化学报, 2021, 42(6): 137-144.
[13]	李豪杰, 王青华, 李军浩, 张延化, . 半喂入花生联合收获机去石清选装置设计与试验[J]. 中国农机化学报, 2021, 42(10): 29-33+58.
[14]	李晓康;张家瑞;韩少平;丁立利;. 9QZL-1.8自走式青贮玉米联合收获机设计与试验[J]. 中国农机化学报, 2020, 41(8): 1-6+19.
[15]	郭红星;金诚谦;印祥;康艳;宁新杰;刘鹏;. 谷物联合收获机清选系统研究现状[J]. 中国农机化学报, 2020, 41(6): 26-36.